Effects of Liquid Polymers on the Strength and Freezing-Thawing Properties of Bentonite and Kaolin Clays: A Comparative Study for Cold Climates
DOI:
https://doi.org/10.7250/bjrbe.2023-18.597Keywords:
bentonite, freezing-thawing, kaolin clay, liquid polymer, stabilization, strengthAbstract
Clay soils can exhibit swelling and settlement behaviour when interacted with water. The clays located in road infrastructure can damage the road pavement and cause cracks because of swelling and/or settlement of clays. The freezing-thawing processes of clay soils can increase the damages of pavement. Additionally, the strength losses can occur. Weak soils can be improved using various soil improvement techniques with or without additives. In this study, liquid polymers (polyurethane, epoxy resin, and styrene acrylic) were combined with clays in various amounts (5 wt.%, 10 wt.%, 15 wt.%, and 20 wt.%) to improve the strength and investigate the freezing-thawing behaviour of high-plasticity bentonite and low-plasticity kaolin clay. Unconfined compression tests and freezing-thawing cycles were performed on the samples with additives that were cured for 1 and 7 days. As a result, it was observed that polyurethane, epoxy resin, and styrene acrylic additives had positive effects on both the unconfined compressive and the post freezing-thawing unconfined compressive strengths of low and high plasticity clays in cold climates.References
Akbulut, R. K., & Zaimoğlu, A. Ş. (2019). Effect of aspect ratio on the freezing-thawing of a clay. Selçuk Üniversitesi Mühendislik, Bilim ve Teknoloji Dergisi, 7(1), 66–74. https://doi.org/10.15317/Scitech.2019.182
Anagnostopoulos, C. A. (2015). Strength properties of an epoxy resin and cement-stabilized silty clay soil. Applied Clay Science, 114, 517–529. http://dx.doi.org/10.1016/j.clay.2015.07.007
Anagnostopoulos, C. A., Kandiliotis, P., Lola, M., & Karavatos, S. (2014). Effect of epoxy resin mixtures on the physical and mechanical properties of sand. Research Journal of Applied Sciences, Engineering and Technology, 7(17), 3478–3490. http://dx.doi.org/10.19026/rjaset.7.700
Anjaneyappa, A. & Amarnath, M. S. (2013). Influence of compaction energy on soil stabilized with chemical stabilizer. International Journal of Research in Engineering and Technology, IC-RICE Conference Issue, 211–215. https://doi.org/10.15623/ijret.2013.0213037
American Society for Testing and Materials. (2003). ASTM D 2166: 2003: Standard test method for unconfined compressive strength of cohesive soil.
Bak Sen, J. W., Yunus, N. Z. M., Saleh, S., Ahmad, K., Rahim, A., & Mat Said, K. (2021). The effect of polyurethane mix ratio on the strength of polyurethane treated marine clay. IOP Conference Series: Materials Science and Engineering, 1144, Article 012079. http://dx.doi.org/10.1088/1757-899X/1144/1/012079
Ghasemzadeh, H., Mehrpajouh, A., Pishvaei, M., & Mirzababaei, M. (2020). Effects of curing method and glass transition temperature on the unconfined compressive strength of acrylic liquid polymer-stabilized kaolinite. Journal of Materials in Civil Engineering, 32(8). http://dx.doi.org/10.1061/(ASCE)MT.1943-5533.0003287
Ghazavi, M., & Roustaie, M. (2010). The influence of freeze-thaw cycles on the unconfined compressive strength of fiber-reinforced clay. Cold Regions Science and Technology, 61(2–3), 125–131. https://doi.org/10.1016/j.coldregions.2009.12.005
Gilazghi, S. T., Huang, J., Rezaeimalek, S., & Bin-Shafique, S. (2016). Stabilizing sulfate-rich high plasticity clay with moisture activated polymerization. Engineering Geology, 211, 171–178. https://doi.org/10.1016/j.enggeo.2016.07.007
Güllü, H. (2015). Unconfined compressive strength and freeze-thaw resistance offine-grained soil stabilised with bottom ash, lime and superplasticise. Road Materials and Pavement Design, 16(3), 608–634. http://dx.doi.org/10.1080/14680629.2015.1021369
Hamidi, S., & Marandi, S, M. (2018). Clay concrete and effect of clay minerals types on stabilized soft clay soils by epoxy resin. Applied Clay Science, 151, 92–101. http://dx.doi.org/10.1016/j.clay.2017.10.010
Holtz, R. D., & Kovacs, W. D. (1981). An introduction to geotechnical engineering (1st ed.). Prentice Hall, New Jersey, USA.
Isik, M. A. (2019). Investigation the effects of resins on the strength and freezing-thawing behaviors of clays [Ms. Thesis, Ataturk University Graduate School of Natural and Applied Sciences].
Kimura, H., Matsumoto, A., Hasehawa, K., Ohtsuka, K., & Fukuda, A. (1998). Epoxy resin cured by bisphenol A based benzoxazine. Journal of Applied Polymer Science, 64, 1903–1910. https://doi.org/10.1002/(SICI)1097-4628(19980620)68:12<1903::AID-APP2>3.0.CO;2-P
Kolay, P. K., & Dhakal, B. (2020). Geotechnical properties and microstructure of liquid polymer amended fine-grained soils. Geotechnical and Geological Engineering, 38, 2479–2491. https://doi.org/10.1007/s10706-019-01163-x
Kolay, P. K., Dhakal, B., Kumar, S., & Puri, V. K. (2016). Effect of liquid acrylic polymer on geotechnical properties of fine-grained soils. International Journal of Geosynthetics and Ground Engineering, 2, Article 29. https://doi.org/10.1007/s40891-016-0071-5
Mirzababaei, M., Arulrajah, A., & Ouston, M. (2017). Polymers for stabilization of soft clay soils. Procedia Engineering, 189, 25–32. https://doi.org/10.1016/j.proeng.2017.05.005
Naeini, S. A., Naderinia, B., & Izadi, E. (2012). Unconfined compressive strength of clayey soils stabilized with waterborne polymer. KSCE Journal of Civil Engineering, 16, 943–949. https://doi.org/10.1007/s12205-012-1388-9
Nowamooz, H. (2016). Resin injection in clays with high plasticity. Comptes Rendus Mécanique, 344(11–12), 797–806. https://doi.org/10.1016/j.crme.2016.09.001
Panda, S. S., Panda, B. P., Nayak, S. K., & Mohanty, S. (2018). A review on waterborne thermosetting polyurethane coatings based on castor oil: Synthesis, characterization, and application. Polymer-Plastics Technology and Engineering, 57(6), 500–522. https://doi.org/10.1080/03602559.2016.1275681
Pham, H. Q., & Marks, M. J. (2005). Epoxy resins. In Ullmann’s encyclopedia of industrial chemistry (pp. 156–238). https://doi.org/10.1002/14356007.a09_547.pub2
Rezaeimalek, S., Nasouri, R., Huang, J., & Bin-Shafique, S. (2018). Curing method and mix design evaluation of a styrene-acrylic based liquid polymer for sand and clay stabilization. Journal of Materials in Civil Engineering, 30(9). https://doi.org/10.1061/(ASCE)MT.1943-5533.0002396
Saleh, S., Yunus, N. Z. M., Ahmad, K., & Ali, N. (2018). Stabilization of marine clay soil using polyurethane. MATEC Web of Conferences, 250, Article 01004. https://doi.org/10.1051/matecconf/201825001004
Saleh, S., Yunus, N. Z. M., Ahmad, K,. Ali, N., & Marto, A. (2020). Micro-level analysis of marine clay stabilised with polyurethane. KSCE Journal of Civil Engineering, 24, 807–815. https://doi.org/10.1007/s12205-020-1797-0
Saygılı, A. (2018). Killi zeminlerin polimerik metil difenil izosiyanit sıvı polimeri ile iyileştirilmesi. DÜMF Mühendislik Dergisi, 9(1), 475–482.
Shi, H., Li, Z., Li, W., Wang, S., Wang, B., & Wang, P. (2021). Effect of freeze-thaw cycles on the mechanical properties of polyacrylamide- and lignocellulose-stabilized clay in Tibet. Advances in Materials Science and Engineering, 2021, Article 7723405. https://doi.org/10.1155/2021/7723405
Şenol, Z. M., Çetinkaya, S., Yenidünya, A. F., Başoğlu-Ünal, F., & Ece, A. (2022). Epichlorohydrin and tripolyphosphate-crosslinked chitosan-kaolin composite for Auramine O dye removal from aqueous solutions: Experimental study and DFT calculations. International Journal of Biological Macromolecules, 199, 318–330. https://doi.org/10.1016/j.ijbiomac.2022.01.008
Tingle, J. S., Newman, J. K., Larson, S. L., Weiss, C. A., & Rushing, J. F. (2007). Stabilization mechanisms of nontraditional additives. Transportation Research Record, 1989-2(1), 59–67. https://doi.org/10.3141/1989-49
Downloads
Published
Issue
Section
License
Copyright (c) 2023 Zeynep Nese Kurt Albayrak, Mehmet Akif Isik
This work is licensed under a Creative Commons Attribution 4.0 International License.
How to Cite
